Can you bend bars?

Talk about anything.

Moderators: Bearbonesnorm, Taylor, Chew

Post Reply
frogatthefarriers
Posts: 497
Joined: Tue Oct 14, 2014 1:31 pm
Location: Wrexham

Can you bend bars?

Post by frogatthefarriers »

I seem to have accumulated a few sets of rather straight handlebars over the years. I was wondering if I could bend the handles on a set to try to find the ideal (for me) sweep angle. Then I could shop for some - to take the expense out of finding the right ones.

Ta! :???:
Konia kują, żaba noge podstawia...
User avatar
BigdummySteve
Posts: 2850
Joined: Sun Nov 20, 2016 9:16 pm
Location: Somewhere over the rainbow

Re: Can you bend bars?

Post by BigdummySteve »

No worries, what’s the worst that could happen?
I’d prefer a steel bar for the experiment and bend them with proper forms/ sand fill them possibly to prevent folding, if it’s just temporary to get a feel and you take it easy I can’t see any major problems.

Just don’t be tempted to keep bending a set of ally bars then ride a World Cup downhill course repeatedly :-bd
We’re all individuals, except me.

I woke up this morning but I’m still in the dark
User avatar
Bearbonesnorm
Posts: 20794
Joined: Sun Jun 05, 2011 8:53 pm
Location: my own little world

Re: Can you bend bars?

Post by Bearbonesnorm »

If they're aluminium then no. If they're steel then you stand a better chance but ideally you'll need heat - lots of heat but even then, they're still likely to crease.
What value a life half lived if the half you lived was the wrong half?
freddy_tanner
Posts: 31
Joined: Sat Jan 13, 2018 4:34 pm

Re: Can you bend bars?

Post by freddy_tanner »

Pretty sure I've read about folks back in the good ol' days bending drop bars, cold setting without heat, out in order to add a flare. Think I remember them being filled with sand too

No idea of bar material though. Steel I can imagine.
User avatar
Charliecres
Posts: 1341
Joined: Tue Oct 01, 2013 1:28 pm

Re: Can you bend bars?

Post by Charliecres »

I think I’d see if anyone on here has some bent bars you could try. Or head over to Planet X and grab some of their not very spendy offerings.

I’ve got some Fleegles and a matching 25.4 clamp stem you can have for postage.
User avatar
htrider
Posts: 3917
Joined: Wed Apr 02, 2014 10:51 pm
Location: Fife
Contact:

Re: Can you bend bars?

Post by htrider »

Steel with a proper pipe bender and mandrell, not ally under any circumstances. Most ally bars will be heat treated post bending and will not then take another bend safely.
Even Cro-mo bars, being hard and thin wall are going to be a challenge to bend and will need to be normalised post bending (heat evenly to a very specific temp and cool in a specific way). There is stuff on the net about doing this but you need to know your sh*t as having a broken bar end go into your wrist as your face hits the stem is not likely to be a positive experience. My advice? buy some more bars and don't take the risk.
middleagedmadness
Posts: 1784
Joined: Wed Nov 01, 2017 6:37 pm
Location: Tir Na Nog

Re: Can you bend bars?

Post by middleagedmadness »

Same as what stu and Phil say ,plus it'll probably cost more for you to get the kit pipe benders and access to oxy acetylene than it would to buy a couple of different cheap bars
And I would have thought you'd want to temper the steel to keep its strength which can be a dark art in itself
frogatthefarriers
Posts: 497
Joined: Tue Oct 14, 2014 1:31 pm
Location: Wrexham

Re: Can you bend bars?

Post by frogatthefarriers »

Thanks for all the replies chaps.

I've got access to some pipe bending stuff, so they'd probably not just crumple and I don't do death-defying stunts - too old - so no heavy loadings in use. I just thought I could give 'em a bit more sweep and try them on my run-around bike and see what angle is best. Then I could shop around and get the right ones first time - and only buy once.
Post Reply