Folks,
Following on from my "what weight of material for a frame bag" thread I thought I'd start a new thread progress my wee project, so here goes.....
I went with 500D Cordura material off Ebay, which has a nice thick robust feel about it,
The plan is to have a full length Velcro fixing along the top tube and either a full length or 2 separate Velcro straps along the short section on the down tube, I feel this should be enough to stop the bag swinging out of position and hitting my legs.
Made the template up for the ECR, had a few ideas in my head but thought I'd try a day pack sort of thing instead of a full on frame bag,
DSC_0069 by Rod K, on Flickr
Pinned 2 sheet together and marked round the template giving 10mm extra along the edge for the hem
DSC_0073 by Rod K, on Flickr
DSC_0075 by Rod K, on Flickr
trimmed off the excess, and found my first goof, I put the 2 sheets the same orientation, so ended up with 2 left hand sides...Doh!
DSC_0076 by Rod K, on Flickr
So quickly cut out another side with the correct orientation this time
DSC_0077 by Rod K, on Flickr
The central section will be a continuous length of material, about 70mm wide in total (50mm + 10mm either side for hem). I'm pondering whether to flare out the front a wee bit to give a touch more room, but I might just be making things more complicated than need be.
the zip (salvaged from an old mo'bike jacket so nice and hefty) will be covered with a flap to help keep water/ muck etc.. out of the bag
Using the scraps I did a test run of stitching 4 sheets together and stitching a test curve, all went well....
hopefully during the week I can time to stitch things together
First Frame pack, first sewing project.. what could go wrong
Moderators: Bearbonesnorm, Taylor, Chew
Re: First Frame pack, first sewing project.. what could go w
update..
Started putting the zip in, and after a few false starts and copious amount of swearing, I finally got it in, not pretty by any means by seems secure
DSC_0078 by Rod K, on Flickr
Then came the flap to cover the zip, a bit better, but improving
DSC_0079 by Rod K, on Flickr
I've cut out the central section that will join both half's together and I flared it out a bit at the front, but this might change as I just realised I was going to put the down tube fixing point here...Doh!
next steps will be the top tube fixing straps, then joining the 2 sides together
Just for the record, hats off to one and all to have done this sort of MYOG project, sewing/ stitching is a lot harder than I expected it to be
cheers Roddy
Started putting the zip in, and after a few false starts and copious amount of swearing, I finally got it in, not pretty by any means by seems secure
DSC_0078 by Rod K, on Flickr
Then came the flap to cover the zip, a bit better, but improving
DSC_0079 by Rod K, on Flickr
I've cut out the central section that will join both half's together and I flared it out a bit at the front, but this might change as I just realised I was going to put the down tube fixing point here...Doh!
next steps will be the top tube fixing straps, then joining the 2 sides together
Just for the record, hats off to one and all to have done this sort of MYOG project, sewing/ stitching is a lot harder than I expected it to be
cheers Roddy
Re: First Frame pack, first sewing project.. what could go w
Not too shabby
Its always a learning curve with sewing, and usually takes 3-4 alterations before you get it perfect, this is normal and part if the learning.
Something I learnt is how dimensions can change, if you forget to take it into account, after sewing the hem and popping right side out it can end up smaller than planned. At the same time certain bags can bulge more than you think. So again, props to you for your first try
How do you plan to add the straps after already sewn the body together?
Its quite common to sew into the seams whilst putting it all together, but I tend to prefer sewing a webbing 'ladder' around the outside edge (like alpkit) as its easier and more modular.
Either way, keep us update and well done
Its always a learning curve with sewing, and usually takes 3-4 alterations before you get it perfect, this is normal and part if the learning.
Something I learnt is how dimensions can change, if you forget to take it into account, after sewing the hem and popping right side out it can end up smaller than planned. At the same time certain bags can bulge more than you think. So again, props to you for your first try
How do you plan to add the straps after already sewn the body together?
Its quite common to sew into the seams whilst putting it all together, but I tend to prefer sewing a webbing 'ladder' around the outside edge (like alpkit) as its easier and more modular.
Either way, keep us update and well done
Re: First Frame pack, first sewing project.. what could go w
Cheers for thatHaYWiRe wrote:Not too shabby ....
The original plan was to do as you suggested and sew the straps into the seams, but since it was an awkward shape for my first attempt, as I plan to have a length of material that will run the length of the top tube and a shorter section for the downtube, its overkill for the size of the bag but its a look I like (shallow, I know but what can I say..), I thought today I'd make that up as a separate patch and stitch this to the top and front edge of the bag, using the large opening to work through, if all else fails then it can always be hand stitched.HaYWiRe wrote:.....How do you plan to add the straps after already sewn the body together?
Its quite common to sew into the seams whilst putting it all together, but I tend to prefer sewing a webbing 'ladder' around the outside edge (like alpkit) as its easier and more modular....
When I make the full triangle type bag I plan to do the webbing strap idea.
as you say 3-4 alterations will get it to a good place....
cheers Roddy
Re: First Frame pack, first sewing project.. what could go w
its done WooHoo!!
I made the flaps a bit long (on purpose honest )
DSC_0085 by Rod K, on Flickr
But I did trim them down a bit except for the top tube as I used one side to be able to wrap round the top tube so there is material under the top tube so it added extra protection as there is line fittings under there.
DSC_0089 by Rod K, on Flickr
An in action, I'm satisfied with the result but know I can do better, but its rock solid with little movement.
DSC_0091 by Rod K, on Flickr
I added a bit of flare to front but its hard to see due to my sewing skills )
DSC_0091 by Rod K, on Flickr
I added a touch of velcro to that seat tube so the end of the pack didnt swing about
DSC_0093 by Rod K, on Flickr
Overall its solid and doesn't move much and when it did a simple knock put it back in position, I just need to lower the water bottle mount a touch to allow easier access to the bottle otherwise happy lad
Again I will say anybody who does this either as a project or a profession hats off to you, as this was more complex than expected and the level of skill needed to work the machine was also surprising.
so hats off to one and all.
cheers Roddy
I made the flaps a bit long (on purpose honest )
DSC_0085 by Rod K, on Flickr
But I did trim them down a bit except for the top tube as I used one side to be able to wrap round the top tube so there is material under the top tube so it added extra protection as there is line fittings under there.
DSC_0089 by Rod K, on Flickr
An in action, I'm satisfied with the result but know I can do better, but its rock solid with little movement.
DSC_0091 by Rod K, on Flickr
I added a bit of flare to front but its hard to see due to my sewing skills )
DSC_0091 by Rod K, on Flickr
I added a touch of velcro to that seat tube so the end of the pack didnt swing about
DSC_0093 by Rod K, on Flickr
Overall its solid and doesn't move much and when it did a simple knock put it back in position, I just need to lower the water bottle mount a touch to allow easier access to the bottle otherwise happy lad
Again I will say anybody who does this either as a project or a profession hats off to you, as this was more complex than expected and the level of skill needed to work the machine was also surprising.
so hats off to one and all.
cheers Roddy
Re: First Frame pack, first sewing project.. what could go w
A Bottle holder that allows side access helps - I use these ones
https://www.evanscycles.com/specialized ... t-EV200585
https://www.evanscycles.com/specialized ... t-EV200585
2924 miles per Gallon
Re: First Frame pack, first sewing project.. what could go w
Nice one, I was looking at using the old wire cage style as they flex a bit more but that looks perfect and it looks like it'll allow a bit of movement in the fitting of the cage as wellMart wrote:A Bottle holder that allows side access helps - I use these ones
https://www.evanscycles.com/specialized ... t-EV200585