Ghetto tubelessing a road wheel
Moderators: Bearbonesnorm, Taylor, Chew
-
- Posts: 9405
- Joined: Tue Sep 20, 2016 8:19 am
- Location: Dewsbury, West Yorkshire
Ghetto tubelessing a road wheel
Hypothetically speaking - though I am keeping an eye on a deep Dura Ace rim thats not tubeless specific - what would be your top few tips should some retard decide to try it...
I'm thinking in no particular order:
Reinforce the tubeless valave area even more than I'd usually from inside and out
Make sure I don't go over tires witmore than 60psi -so that'd mean a 32c tyre as the minimal.
Wrap extra tubeless tape whilst sealing it all and ensure the edges are covered fully - so maybe they might give me an extra few psi of pressure leeway...
Keep an eye around the rim for cracking prematurely
______
What have a missed
I'm thinking in no particular order:
Reinforce the tubeless valave area even more than I'd usually from inside and out
Make sure I don't go over tires witmore than 60psi -so that'd mean a 32c tyre as the minimal.
Wrap extra tubeless tape whilst sealing it all and ensure the edges are covered fully - so maybe they might give me an extra few psi of pressure leeway...
Keep an eye around the rim for cracking prematurely
______
What have a missed
-
- Posts: 8144
- Joined: Mon Mar 18, 2013 9:56 am
Re: Ghetto tubelessing a road wheel
Take out a life insurance policy?
- fatbikephil
- Posts: 6589
- Joined: Wed Apr 02, 2014 10:51 pm
- Location: Fife
- Contact:
Re: Ghetto tubelessing a road wheel
I tried it once Shaff but it didnae work. There are no flat bits in a normal road rim to hold the tyre bead in place so it would inflate but unseat almost immediately and lose all pressure.
Road tubeless is a bit iffy anyway as the pressures are so high the sealant general doesn't other than for thorns or tacks.
Road tubeless is a bit iffy anyway as the pressures are so high the sealant general doesn't other than for thorns or tacks.
-
- Posts: 9405
- Joined: Tue Sep 20, 2016 8:19 am
- Location: Dewsbury, West Yorkshire
Re: Ghetto tubelessing a road wheel
Yes... this is whats stopped me from experimentation all these years... Though before they started doing proper tubeless wheels I did ghetto tubeless some 'HPLUS sons' but they're super strong things that I could afford to experiment with...
-
- Posts: 9405
- Joined: Tue Sep 20, 2016 8:19 am
- Location: Dewsbury, West Yorkshire
Re: Ghetto tubelessing a road wheel
Thanks, erm, Phil ( did I get it right... surely you can't be Dave again bloomin dyslexia)... Yeah, the pressures are a pest on road tubeless. Anything above 70psi and I reckon it's mental to even consider. But between 60 and 75 I've had good results of em sealing a hole out. Obviously it was a thorn or something stuck in there to help plug the hole.htrider wrote: ↑Thu Apr 15, 2021 8:04 pm I tried it once Shaff but it didnae work. There are no flat bits in a normal road rim to hold the tyre bead in place so it would inflate but unseat almost immediately and lose all pressure.
Road tubeless is a bit iffy anyway as the pressures are so high the sealant general doesn't other than for thorns or tacks.
I've been on the road tubeless (proper tr wheels and tires) for the past 3 or almost 4 years now and really love it)...
- fatbikephil
- Posts: 6589
- Joined: Wed Apr 02, 2014 10:51 pm
- Location: Fife
- Contact:
Re: Ghetto tubelessing a road wheel
Phil it is
I've never had much luck tubeless within anything other than plus or fat bike tyres. Must just be me...
I've never had much luck tubeless within anything other than plus or fat bike tyres. Must just be me...
Re: Ghetto tubelessing a road wheel
I've been running "Ghetto" tubeless on a pair of Mavic Kysrium (non tubeless) disc wheels for two years now, no issues at all with tyres unmounting (though its always on your mind). Gorilla tape and Stans sealant, working a treat for sealing and p repair. 28mm tubeless tyre @ 65psi
-
- Posts: 462
- Joined: Mon Nov 18, 2019 7:42 pm
- Location: Cumbria
Re: Ghetto tubelessing a road wheel
I've used Gorilla Tape and Stans on my old Hybrid too. It can be a PITA to get the tyre seated (Maxxis Ramblers were ok, WTB Nanos turned out to be a bit of an ordeal). I run 30PSI on the front, 40 or 50 on the back depending on whether I'm mainly on or off road. That's on a 700C wheel with 40mm tyres.Delv4 wrote: ↑Fri Apr 16, 2021 4:24 pm I've been running "Ghetto" tubeless on a pair of Mavic Kysrium (non tubeless) disc wheels for two years now, no issues at all with tyres unmounting (though its always on your mind). Gorilla tape and Stans sealant, working a treat for sealing and p repair. 28mm tubeless tyre @ 65psi
“I want to see the wild country again before I die, and the Mountains..."
Bilbo Baggins.
Bilbo Baggins.
Re: Ghetto tubelessing a road wheel
I ran ghetto tubeless for over 3 years on non tubeless Campy rims with tubeless tyres. I had no issues, pressure front was circa 80 and rear 85. Over and above rim tape I wrapped the rim with 2 or 3 continuous wraps of heavy duty cling film (plenty on Amazon or eBay). I have a fair bit of tubeless experience going back to circa 2006 on my Turner Flux but honestly it was relatively easy to do. My main reason for doing this on a road bike was simply to see if I could and what it was like to ride.
-
- Posts: 9405
- Joined: Tue Sep 20, 2016 8:19 am
- Location: Dewsbury, West Yorkshire
Re: Ghetto tubelessing a road wheel
Thanks Cumbrian (sorry, forgot name )... problem with anything above 65psi is that you end up double guessing if/when the sidewalls are gonna give up. 60 psi is probably the lowest I would be able to run on 28c/32c road tires...The Cumbrian wrote: ↑Sun Apr 18, 2021 2:24 pmI've used Gorilla Tape and Stans on my old Hybrid too. It can be a PITA to get the tyre seated (Maxxis Ramblers were ok, WTB Nanos turned out to be a bit of an ordeal). I run 30PSI on the front, 40 or 50 on the back depending on whether I'm mainly on or off road. That's on a 700C wheel with 40mm tyres.Delv4 wrote: ↑Fri Apr 16, 2021 4:24 pm I've been running "Ghetto" tubeless on a pair of Mavic Kysrium (non tubeless) disc wheels for two years now, no issues at all with tyres unmounting (though its always on your mind). Gorilla tape and Stans sealant, working a treat for sealing and p repair. 28mm tubeless tyre @ 65psi