Way OT question about 240V transformer.
Moderators: Bearbonesnorm, Taylor, Chew
- Bearbonesnorm
- Posts: 23940
- Joined: Sun Jun 05, 2011 8:53 pm
- Location: my own little world
Way OT question about 240V transformer.
I've just received a 240V - 50V AC tranformer and in the space of 30 to 40 seconds it's now knackered It's for a feather burner I'm making for someone, anyway wired up the 2 primary connectors to a 5 amp fused plug and plugged it into the socket. Checked to see what the output was and both pairs of secondry connectors showed 26V which was as expected and all good.
Then connected 1 pair of secondary connectors to the burner (think hot wire cutter) and the wire heated nicely within 10 seconds. However, after a further 20 seconds I noticed a little smoke coming from the transformer ... so I unplugged it as you would. I now have that lovely burnt transformer smell and no output.
Any ideas before I conclude it's simply a crap transformer? Could only using 1 secondary output have burnt the secondary windings out?
Ta.
Then connected 1 pair of secondary connectors to the burner (think hot wire cutter) and the wire heated nicely within 10 seconds. However, after a further 20 seconds I noticed a little smoke coming from the transformer ... so I unplugged it as you would. I now have that lovely burnt transformer smell and no output.
Any ideas before I conclude it's simply a crap transformer? Could only using 1 secondary output have burnt the secondary windings out?
Ta.
May the bridges you burn light your way
Re: Way OT question about 240V transformer.
Are you using a 240v/50v transformer or a 240v/50v/50v transformer? The description differs from the first sentence.
How is 26v output from 50v secondary terminals "good"?
What current does the load draw?
What current is the transformer designed to supply?
Do the instructions specify both outputs must be used simultaneously?
How is 26v output from 50v secondary terminals "good"?
What current does the load draw?
What current is the transformer designed to supply?
Do the instructions specify both outputs must be used simultaneously?
May you always have tail wind.
- Bearbonesnorm
- Posts: 23940
- Joined: Sun Jun 05, 2011 8:53 pm
- Location: my own little world
Re: Way OT question about 240V transformer.
Sorry Pete, it's 240v primary with 2 x 24v secondary.Are you using a 240v/50v transformer or a 240v/50v/50v transformer?
Instructions? It does state that the secondary outputs are independent but can be wired in series or parallel.Do the instructions specify both outputs must be used simultaneously?
Rated at 50VA max.What current is the transformer designed to supply?
Don't know without working it out.What current does the load draw?
May the bridges you burn light your way
Re: Way OT question about 240V transformer.
It's the actual load it draws that's critical, more so than the theoretical load (but theoretical load will indicate whether the transformer is at risk of being overworked or not).Bearbonesnorm wrote:Don't know without working it out.What current does the load draw?
Has the load been produced by a manufacturer that states the current drawn; or is it home-made?
May you always have tail wind.
- Bearbonesnorm
- Posts: 23940
- Joined: Sun Jun 05, 2011 8:53 pm
- Location: my own little world
Re: Way OT question about 240V transformer.
Oh, very much a home brewed affair Pete. Basically, it's a 1mm Ni-chrome wire element.Has the load been produced by a manufacturer that states the current drawn; or is it home-made?
There's an outfit in the US that sells transformers for hot wire cutters which is where I gleaned the transformer spec' from.
May the bridges you burn light your way
- NewRetroTom
- Posts: 284
- Joined: Thu Jun 05, 2014 12:09 pm
- Location: Chamonix
Re: Way OT question about 240V transformer.
Have you got a multi-meter you could use to measure the resistance of this wire element? If you know that you should be able to work out how much current will flow at a given voltage.
Re: Way OT question about 240V transformer.
Is it possible to measure the resistance of the load (using an Ohm meter), then calculate the current it will draw?
This may help (see example 1) http://www.electronics-tutorials.ws/acc ... tance.html
(You don't have to draw the phasor diagram if you don't want to )
This may help (see example 1) http://www.electronics-tutorials.ws/acc ... tance.html
(You don't have to draw the phasor diagram if you don't want to )
May you always have tail wind.
- Bearbonesnorm
- Posts: 23940
- Joined: Sun Jun 05, 2011 8:53 pm
- Location: my own little world
Re: Way OT question about 240V transformer.
Resistance is 3 ohms which at 24v should give a draw of 8 amps. Can't see why that should have blown the transformer?
May the bridges you burn light your way
Re: Way OT question about 240V transformer.
Was it a robot in disguise?
- Bearbonesnorm
- Posts: 23940
- Joined: Sun Jun 05, 2011 8:53 pm
- Location: my own little world
Re: Way OT question about 240V transformer.
Took me a few seconds Mike.
May the bridges you burn light your way
Re: Way OT question about 240V transformer.
Morning!
Where were we...? Ah, yes...
"KVA is simply the load voltage times the load current"
So: based on the spec of your transformer:
50VA = 24v x "maximum current it can cope with"
...and manipulating the equation gives...
50 divided by 24 = "maximum current it can cope with"
So, 50/24 = 2.0833 Amps = maximum current the transformer can cope with.
Thus: 50VA + 24v + 8 Amps = Smoke!
So why didn't the fuse blow? Well; this article https://electronics.stackexchange.com/q ... -blow?rq=1 states fuses blow when excessive current is drawn for a period of time, the key point being the relationship between "rate of current increase" and "time" in this case.
This article https://www.physics.ohio-state.edu/~p61 ... rrent.html (and many others like it) states "...currents between 100 and 200 mA (0.1 to 0.2 amp) are lethal."
The chart is worth a look, too:
https://www.physics.ohio-state.edu/~p61 ... urrent.gif
Worth remembering when tinkering about in the shed. Fun though it may be; personally I'd consign the home-made thing to the bin, then buy a system designed and made by a competent manufacturer that's within the capability of the transformer.
Please be careful.
Pete
Where were we...? Ah, yes...
Correct so far. However: this article by a transformer manufacturer...http://www.csanyigroup.com/transformer-ratings...statesBearbonesnorm wrote:Resistance is 3 ohms which at 24v should give a draw of 8 amps.
"KVA is simply the load voltage times the load current"
So: based on the spec of your transformer:
50VA = 24v x "maximum current it can cope with"
...and manipulating the equation gives...
50 divided by 24 = "maximum current it can cope with"
So, 50/24 = 2.0833 Amps = maximum current the transformer can cope with.
Thus: 50VA + 24v + 8 Amps = Smoke!
So why didn't the fuse blow? Well; this article https://electronics.stackexchange.com/q ... -blow?rq=1 states fuses blow when excessive current is drawn for a period of time, the key point being the relationship between "rate of current increase" and "time" in this case.
This article https://www.physics.ohio-state.edu/~p61 ... rrent.html (and many others like it) states "...currents between 100 and 200 mA (0.1 to 0.2 amp) are lethal."
The chart is worth a look, too:
https://www.physics.ohio-state.edu/~p61 ... urrent.gif
Worth remembering when tinkering about in the shed. Fun though it may be; personally I'd consign the home-made thing to the bin, then buy a system designed and made by a competent manufacturer that's within the capability of the transformer.
Please be careful.
Pete
May you always have tail wind.
- Bearbonesnorm
- Posts: 23940
- Joined: Sun Jun 05, 2011 8:53 pm
- Location: my own little world
Re: Way OT question about 240V transformer.
Thanks for that Pete, I'll take a look at those links. It's the same spec transformer as used in hot wire cutters, so somethng's a miss somewhere.
andFun though it may be; personally I'd consign the home-made thing to the bin, then buy a system designed and made by a competent manufacturer that's within the capability of the transformer.
Neither of the above computePlease be careful.
May the bridges you burn light your way
Re: Way OT question about 240V transformer.
Yes - 50VA is the total rating for the transformer. it's almost certain that each of your secondaries is (was) only rated for half that (~1 amp @24V).Could only using 1 secondary output have burnt the secondary windings out?
Your calculation is correct. The resistance of the nichrome will increases a bit with temperature, but it still looks like too much load for your transformer.Resistance is 3 ohms which at 24v should give a draw of 8 amps
There's a table here (near the end) that gives the current needed to heat various wire diameters to various temperatures - a 1mm diameter wire need ~10 amps to get to ~500°C.
Is it possible that the US device uses a thinner gauge of wire? (Thinner wire has more resistance for a given length, although you'd need to go down to ~0.25mm wire to match that transformer spec.)
(A 5 amp mains fuse will supply 1200VA before it breaks into a sweat, btw.)
- Bearbonesnorm
- Posts: 23940
- Joined: Sun Jun 05, 2011 8:53 pm
- Location: my own little world
Re: Way OT question about 240V transformer.
Lovely, thanks for that lot Andy, that chart is most useful. I shall order some thinner gauge wire ........ and a new transformer
May the bridges you burn light your way
- BigdummySteve
- Posts: 2974
- Joined: Sun Nov 20, 2016 9:16 pm
- Location: Somewhere over the rainbow
Re: Way OT question about 240V transformer.
I take it that the device only needs to operate for a short time? If so you could use a ‘mod’ ( a device for powering e-cigs) one which uses twin 18650 batteries should be able to heat a short length of wire easily, failing that another battery device might work.
We’re all individuals, except me.
I woke up this morning but I’m still in the dark
I woke up this morning but I’m still in the dark
- Bearbonesnorm
- Posts: 23940
- Joined: Sun Jun 05, 2011 8:53 pm
- Location: my own little world
Re: Way OT question about 240V transformer.
I had thought about an smps Steve.failing that another battery device might work.
May the bridges you burn light your way
- Bearbonesnorm
- Posts: 23940
- Joined: Sun Jun 05, 2011 8:53 pm
- Location: my own little world
Re: Way OT question about 240V transformer.
Thanks for the input folks ... now all sorted
May the bridges you burn light your way
- Bearbonesnorm
- Posts: 23940
- Joined: Sun Jun 05, 2011 8:53 pm
- Location: my own little world
Re: Way OT question about 240V transformer.
Yes Pete.Is it earthed?
May the bridges you burn light your way
Re: Way OT question about 240V transformer.
Stu sparked off a thread, there was some resistance at first but we finally got to the current situation. OMG.Zippy wrote:Watt is all this chatter
We go out into the hills to lose ourselves, not to get lost. You are only lost if you need to be somewhere else and if you really need to be somewhere else then you're probably in the wrong place to begin with.
- danielgroves
- Posts: 395
- Joined: Sun Mar 02, 2014 9:55 pm
- Location: Bath/Bristol, UK
- Contact:
Re: Way OT question about 240V transformer.
Not bad for a Ohm project.
Adventures and Photography Blog: danielgroves.net/adventures-photography
Twitter: @danielsgroves
Instagram: @danielsgroves
Photography on Facebook: facebook.com/danielgrovesphotography
Photography on Instagram: @danielgrovesphotography
Twitter: @danielsgroves
Instagram: @danielsgroves
Photography on Facebook: facebook.com/danielgrovesphotography
Photography on Instagram: @danielgrovesphotography
Re: Way OT question about 240V transformer.
This all seems like a lot of faff when a pair of scissors could have cut those feathers instead
- Bearbonesnorm
- Posts: 23940
- Joined: Sun Jun 05, 2011 8:53 pm
- Location: my own little world
Re: Way OT question about 240V transformer.
This ^ is true. However, in my defence I will say:This all seems like a lot of faff when a pair of scissors could have cut those feathers instead
Scissors tend to leave a jagged edge on the feather which is both unsightly and more importantly, effects flight.
It's hard to cut intricate shapes with scissors, especially on small feathers.
When someone asks me to make them something, I try and do it to the best of my ability and produce something as nice as I can.
... but yeah, you're right
May the bridges you burn light your way